Loading...

FiberPlex Yamaha MY Cards VIM-MY32

SKU: 1471 Category:

$0.00

Description

Overview

The LightViper VIM-MY32 YGDAI cards are designed for use with Yamaha™ digital equipment containing YGDAI (Yamaha General Digital Audio Interface) card slots. The VIM-MY32 cards are used in place of the VIM-1832 at the “tail” or mixer end of the system.

The VIM-MY32 cards can be used in connection with the VIS-1832 or VIS-4832. When used with the VIS- 4832 and Yamaha™ AD8HR mic pre-amps, The Yamaha™ AD8HR mic pre-amps can be remotely controlled through the LightViper system using a Yamaha™ console. VIM-MY32M Master Card – this card provides 16 direct digital inputs (sends) and 8 digital outputs (returns) from the Yamaha™ device.

The VIM-MY32M comes standard with LC fiber connectors however it can also be fit with ST, Neutrik Duo or Neutrik Quad tactical connectors. The VIM-MY32M contains multimode optics (singlemode optional).

The VIM-MY32M contains the clock for the LightViper system. There is an internal switch to select whether the VIM-MY32M is the master clock, or whether the VIM-MY32M will slave to the consoles master clock. The VIM-MY32 cards only operate at 48k. The VIM-MY32M provides 2 fiber-optic pass thru connectors which allow inputs 17-32 to be fed into a second master card. There is a “sync” status LED on the front of the VIM-MY32M. This LED will be solid green when in sync, flashing red and green while looking for sync, and solid red when no sync is present.

The VIM-MY32M contains a Neutrik MiniCon® connector to enable connection to the VIM-MY32S slave card. VIM-MY32S Slave Card – there is no fiber-optic connection to the VIM-MY32S slave card. It connects to the VIM-MY32M master card via the supplied MiniCon® cable. The VIM-MY32S also contains an RJ45 connector for TTL data input, and a DB9, both of which can be used for sending Yamaha™ HA remote control over fiber with the audio returns. The toggle switch is used to choose which connector is active – the TTL connector or the DB9 connector. To use the TTL data port for Yamaha HA remote control, a LightViper DGL-422 dongle is required.

Additional information

Weight 5.00 lbs
Dimensions 5.00 × 5.00 × 5.00 in

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Features

  • 32×8 FiberOptic Audio Transport
  • Digital direct input to Yamaha™ YGDAI card slots
  • Optical distribution of Word Clock
  • Transports Yamaha™ HA remote control
  • Ultra-low latency cable runs over 1.25 miles with no loss

Specifications

GENERAL SPECIFICATIONS
 
Min
Typ
Max
Power Consumption From Card Slot (W)
3.5
 
THD+N (1kHz@ +4dBu) < 0.01%
Frequency Response (20-20kHz @ +16 dBu) ± 0.5 dB
Dynamic Range 102 dB
Crosstalk 5 dB above noise floor
Sampling Rate 24 bit / 96kHz or 24 bit / 48 kHz
Latency 630 µs analog input to analog output, 20 µs, digital input to digital output
 
Environmental Storage Temperature (°C)
-40
85
OperatingTemperature (°C)
0
50
PHYSICAL DIMENSIONS
Height
Width
Length
Weight
1.575 in (40 mm)
4.74 in (100 mm)
6.392 (161 mm)
0.8 lb (0.4 kg)
OPTICAL CHARACTERISTICS
Fiber
Size
Max Distance
Wavelength
Output Power
RX Sens Loss Budget
Multimode
62.5 / 125 µm
2 km
820 nm
-18 dBm
-30 dBm
12 dB
Singlemode
9 /125 µm
20 km
1300 nm
-15 dBm
-32 dBm
21 dB

Ordering Information

 

oi_VIM-MY32.png