Loading...

Loop Telecom L2 Industrial FE DIN Switch IP6810 / Loop-IP6810-IS-SFPC-IDC24-IDC24-G

SKU: 3200 Category:

$0.00

Description

The Loop-IP6810 is a self-healing ring network termination unit (NTU) with a built-in L2 switch. It can be desktop, wall or DIN rail mounted. LEAPS, RSTP, or MSTP* Ethernet Ring protection or point-to-point protection is made possible in 100 Base-FX networks with the IP6810.

All end equipment can be either in packet format via Ethernet ports or serial data via RS232/485 interfaces which will be converted into packet format within the IP6810. The IP6810 has two WAN optical and electrical interfaces, two RS232/485 DTE interfaces, three Ethernet LAN interfaces, two sets of dry contact IN/OUT interfaces, and one alarm relay connector. The IP6810 comes in an industrial hardening mode to support temperatures from -20°C to 70°C (-4°F to 158°F).

The IP6810 supports auto-discovery to locate all units on the ring, and also supports remote configuration for ease of installation.Single AC, single DC or dual DC is supported based on field requirements. Power over Ethernet (PoE) option is also available.

The IP6810 facilitates automation systems, SCADA systems, surveillance systems, traffic control systems, transportation systems and IP networking with robust protection in ring, point-to-point, or omnibus-like topology. Easy installation and configuration make maintenance and further expansion more efficient and cost-effective.

Additional information

Weight 5.00 lbs
Dimensions 12.00 × 12.00 × 12.00 in

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

  • Full frontal access (ETSI) unit complies with IP30 standard
  • Desktop, wall, or DIN Rail mounting
  • Compact intelligent FX packet optical ring with Layer 2 switching capabilities
  • WAN port with OA&M functionality
    • Dual SFP optical housing interfaces
    • Dual RJ45
  • Tributary ports
    • 3 ports 10/100 BaseT Ethernet (with PoE option available in DC 48 only)
    • 2 ports RS232/485 interfaces, user selectable via 2-port DIP switch
    • 2 dry contact for input and 2 dry contact for output; support point-to-point and point-to-multi-point
  • Power modules
    • On-board fixed single AC supply
    • On-board fixed single/dual DC modules with dual feed
  • Auto-discovery topology, auto-diagnostic and remote-configure for easy plug-and-install (up to 64 units)
  • Supports SNTP
  • Ethernet Functionality
    • Loop Ethernet Automatic Protection Switching (LEAPS)
      • Fault recovery time: less than 50 ms
      • Point-to point: fault recovery time less than 8 ms
      • Up to 15 units: fault recovery time less than 25 ms
    • IEEE 802.1w RSTP, 802.1s MSTP*
    • IEEE 802.3x Flow Control, 802.1q Port Base VLAN / Port Isolation
  • Up to 1024 MAC addresses
  • Built-in BERT
  • High speed, asynchronous RS232/RS485 for point-to-point, point-to-multi-point, or omnibus-like applications
  • Master/Slave units setting by using DIP switch
  • Auto-negotiating or forced speed for speed and full/half duplex for Ethernet ports
  • Full/half duplex for tributary Ethernet ports
  • Alarm relay and ACO (Alarm Cut Off) button
  • Remote firmware download via TFTP & Z modem
  • Remote configuration upload & download via TFTP
  • Management port and interface
    • In-band management
    • RS232 console via DB9 connector
    • SNMP v1, v3
    • SSH v2
    • Telnet
    • IEEE 1613, IEC61850-3 (for DC -48 Vdc only)
  • RoHS compliant

RoHS compliant units are identified by the letter G appearing at the end of ordering code.

Part Number Description Notes