The BRX-XLR-24-1S incorporates a BRX-XLR-24-S factory installed in an Emerson CAD-12 pedestal to serve up to 24 ADSL / ADSL2+ subscribers in a customer service area (CSA) with enough room to handle a 100-pair binder from the Central Office (CO or Exchange) and a 100-pair binder toward the subscriber CPE devices.
- High performance and cost effective subscriber loop extension
- Re-use existing right-of-way and eliminate complex civil engineering work
- Strict adherence to ADSL2+ / ADSL Standards
- Extended operating temperature
- Powered from sealing current (max 2mA or 100mW per pair)
- Flexible packaging options (1, 2, 8, 24 and 48 pairs)
| Feature |
Description |
| xDSL Standards |
ITU G.992.5 ADSL2+ Annex A, ITU G.992.3 ADSL2 Annex A, ITU G.992.1 ADSL Annex A |
| Reach Improvement |
Extends ADSL/ ADSL2/ ADSL2+ broadband CSA coverage up to two times its current value |
| Rate Improvement |
Improves effective bandwidth for ADSL/ ADSL2/ ADSL2+ loops up to five times |
| PSD Mask Compliance |
Compliant with ANSI T1.413 and ETSI TS 101 830-1 |
| Signal to Noise Ratio |
Improves the Signal to Noise Ratio (SNR) |
| Power Draw |
Maximum power drawn is 100 mw per pair from the 48V sealing current from the CO or DSLAM/ MSAN |
| Enclosure |
Flexible shelf design allows more subscribers to be added in the future |
| Over-current Protection |
8/20 µsec, 10 kA (1 operation), 10/700 µsec, 6 kV, 300A (50 operations) |
| Regulatory Compliance |
Tested to IP65, UL/CSA and FCC part 15 Class A, WEEE and ROHS compliant |
| Operating Temperature |
-40 to +65 °C |
| Relative Humidity |
5% to 95%, non-condensing |
| Dimensions |
|
| |
BRX-XLR-M: 8” x 5” (203 mm x 127 mm) |
| |
BRX-XLR-1: 9.25” x 5.5” x 1.5” (235 mm x 140 mm x 38 mm) |
| |
BRX-XLR-2: 9.25” x 5.5” x 1.5” (235 mm x 140 mm x 38 mm) |
| |
BRX-XLR-8: 11.5” x 5.5” x 4.7” (292 mm x 140 mm x 120 mm) |
| |
BRX-XLR-24: 21.5” x 17” x 11” (546 mm x 432 mm x 280 mm) |
| Installation Location |
Installed adjacent to a splice point or cross connect cabinet in the outside plant (OSP), No equipment needed in the Central Office / Exchange |
| Auto-Provisioning |
Automatic gain control with no software or hardware configuration, self-adjusts based on loop length and line conditions between the DSLAM and the CPE |
| Number of Ports per Module |
Each BRX-XLR-M module incorporates two (2) independent copper pairs, 100% transparent to pair bonding (if used) |
| Part Number |
Description |
| BRX-XLR-24-1SF |
BRX-1 (emerson CAD-12) Pedestal factory-installed with 24-pair shelf (BRX-XLR-24S) and 12 BRX-XLR-M modules (total 24 amplified ADSL2+ pairs) |
